UTV International Logo
Your source of innovative and cost effective solutions in track and truck vehicles
1-800-985-8665

The Achiever DLT2-60 Tracked Aerial with Jib is designed for stability, simplicity & ease of use for Aerial and Material Handling work. Very low 2.44 psi ground pressure (with 29″ tracks) and high power to weight ratio allows this unit to work where other machines cannot go. Max fording with this unit is up to 36 inches of water. The Achiever DLT2-60 is a top center mount jib & winch configuration.

The Achiever / Dur-A-lift combination DLT2-60 provides a working height of 65 ft with the 22″ elevator and a single (24″ x 30″ x 42″) or double man (24″ x 42″ x 42″) hydraulically rotating bucket with optional 1,000 lb capacity material handling jib.  A 42″ wide bucket can also be mounted without a material handling winch & jib.  Hydraulic jib tilt and continuous rotation is standard on the boom. The hydraulically leveled bucket rotates through 180o.  Each radial corner mounted outrigger extends at 45o to provide an exceptionally stable platform.  The boom is dielectrically tested and certified 46 kV Category “C”.

Longer (59″) front outriggers with 18″ x 20″ pads are standard at the front of the unit and extra-long (71″) outriggers are standard at the rear and provide higher lift on hills (allows deck levelling to within 5o on 12o slopes).  71″ outriggers can also be optionally mounted in the front position.

Some available options are: Basket Liner, Basket Cover, Tool Trays, Main Boom Fiberglass Insert, Articulating Arm Glass Insert, 12 Volt Emergency Boom Rotation & Lowering, Controls with High Electrical Resistant Components (HERC), Tool Circuit at Basket and / or Base, Hydraulic Basket Leveling at Lower Controls and Hydraulically Extendible Jib. The 134 HP Tier IV Deutz AG electronic engine has cold start options down to -30ºF / -35ºC and a 17,000 BTU 12v engine coolant heater with a programmable 7 day timer is also available.

Total completed vehicle weight is approximately 19,000 lbs combined with the generously sized engine provides a greater power to weight ratio than any other 65 ft tracked aerial. The difference when climbing hills in your area will be noticeable. 29″ rubber tracks are standard, optional 33″ tracks are available to provide even lower ground pressure down to 2.15 psi. One man open cab is standard, closed cab is available. Maximum speed is 7.3 mph.

It is transportable on a 15 ton trailer behind a line truck.  Rubber tracks allow unloading on pavement.

UTV has manufactured tracked vehicles since 1995, tracked digger derricks since 1999 & tracked aerials since 2013.  Our customers include many power companies, coops, telecom companies and power line contractors.  We service and support every machine we have ever made.

 

More Pictures for Achiever DLT2-60 Tracked Aerial

↑ Scroll to top

 

 

Request a Quote

  • Click to see what a New Achiever DLT2-60 DU Tracked Aerial includes

    • Cab: 1-Man Open Cab, 24.000 lbs ROPS certified
    • Mechanical suspension seat with 2 point seat belt
    • Full instrumentation, illuminated panel gauge
    • Backup alarm and horn, 1 fire extinguisher in cab
    • Lights: LED high power lights, 2 front & 1 rear on cab, 1 strobe (top), rear back up (& working) light
    • Engine: Deutz TCD 3.6 L4, 4 cyl, tier 4 turbocharged diesel 134 HP at 2,300 RPM & 369 ft lbs at 1,600 RPM with 120 amp alternator, block heater, glow plugs, secondary fuel filter with water separator, muffler, electric engine shut down system, 2.6 gallon DEF tank
    • Electric engine shutdown system
    • Power Train: Hydrostatic two speed system with oil bath idler hubs
    • Steering: Dual joystick cable control
    • Track: 29″ rubber track with solid rubber tires
    • Wheels: 2 drive sprockets, 2 solid idler wheels, 8 solid rubber wheels, complete set of dust cap retainers for road wheels
    • Suspension: Torsion axle
    • Boom: Center top mounted winch and jib
    • 22″ vertical travel basket elevator
    • 24″ x 42″ x 42″ double man fiberglass basket with step
    • Safety harness and 6′ decelerating lanyard
    • Hyd leveled basket (power stow at upper controls)
    • Upper 4 axis single hand joystick control lever
    • Controls with lockouts in upper control pod
    • Basket rotator, winch, and jib controls
    • 360° continuous rotation, 100° basket rotator
    • Fiberglass extension boom with rubber boom support
    • Lower control levers with upper control override
    • Hydraulic basket leveling at lower controls (2nd location)
    • Lower winch control, hydraulic jib tilt
    • Main boom lifting eye (750 lbs capacity)
    • Deck step basket mounting, 46 KV category “C” insulation
    • Rachet boom tie down front and back
    • Frame:  Corten welded tub, corrosion resistant black
    • Sub Frame: All welded steel with 4 radial outriggers, automotive white
    • Outriggers: Longer(59″ in the front and 71″ in the rear radial outriggers at 45° for higher lift on hills with 18″ x 20″ feet
    • Misc: 2″ square receiver socket, front & rear
    • Front and rear rectangular ground lugs
    • Removeable cab entrance step, 2x removable side deck ladders
    • 2 sets of operations and parts and service manuals
↑ Scroll to top

 

 

Keywords for Achiever DLT2-60 65 ft Tracked Aerial : D Dent Tracks, Dual Person Bucket, Low Ground Pressure, Material Handler, rubber tracks